For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab.

If you reside in an EU member state besides UK, import VAT on this purchase is not recoverable.

Contact the seller - opens in a new window or tab and request postage to your location.

User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign.

A warning message will be displayed if one hour has not elapsed from when the power was turned ON. 3-2.

Conforms to specifications and functions (wavelength accuracy, resolution and photometric accuracy, etc.) laid down in the European, USA and Japanese Pharmacopoeias.

Supports IQ and OQ.

Compact, light spectrophotometer LCD and designated keys enhance ease of operation.

Intended Use Receiving service training is a prerequisite for the correct use of this manual.

Note that Shimadzu will not bear responsibility for problems that may occur when a person who has not received specific service training operates the instrument according to this manual.

Be sure to thoroughly read the instruction manual in advance and adhere to instructions provided when replacing lamps or fuses to avoid injuries such as burns and electric shocks.

WARNING DANGER, High Temperature The light source and light source compartment become extremely hot during operation.

To replace the lamp, turn the power OFF, wait at least ten minutes for the lamp to sufficiently cool.

Warning label WARNING DANGER, Electric Shock Be sure to turn OFF power and disconnect power cable before replacing a fuse to avoid electric shock.

Be sure to adhere to the procedures in this chapter when performing installation work so that the instrument performs appropriately to ensure customer satisfaction.

Inspection of Parts 2.2 Selection of Installation Site 2.3 Installation of UV Instrument Baseline Correction 2-1.

Table2-1 Standard Contents Description PN Qty.

Spectrophotometer UV-1700 Main unit 1 For 230V CE area For 100V area For 120V area For 220V area For 240V area Standard Accessories (One of the following) For 100V-120V area For 220V-240V area AC Power Cable (One of the following) 1 For 100V-120V area For 220V-240V area Fuse (One of the following) 2 4.0A (For 100V-120V) area 2.0A (For 220V-240V) area Grounding Adaptor ( For100V-120V only ) Instruction Manual (Installation Maintenance) 4 Instruction Manual (Operation) Certificate of Compliance.

Therefore the installation site needs to be at least W 700 x D 500mm.

A power switch and cooling fan are mounted on the left side of the main unit.

Install the instrument in a location where ventilation will not be hindered.

Be sure to use a power supply of at least 130VA (if a PC system is to be used, PC and printer power supplies must be taken into consideration as well).

Use a low-voltage instrument if voltage fluctuation exceeds 10 Grounding The UV-1700 power cable has three wires including a ground wire.

If the power outlet does not have ground terminal, be sure to ground the instrument using the ground terminal of the standard accessory ground adapter ( ) or the ground terminal on the left side of the instrument Instrument Installation and Power Cable Connection 1) Install UV-1700 in location that will not hinder ventilation for cooling fan situated on left side of instrument.

Check that the power switch on the main unit is OFF (with O pressed).

Check that the voltage setting of the input voltage changeover switch corresponds to the working supply voltage.

If differing power voltages are displayed, open the fuse holder using a slotted screwdriver, pull out the round plug and insert it at the location displaying the used power voltage.

Check that a 4.0A fuse is used in the 100V system and that a 2.0A fuse is used in the 200V system.

Insert the provided power cable to the power connector on the left side of the main unit.

Insert the power cable in the power outlet.

D2 Lamp: Input item No.

Instrument baseline correction requires Fig.2-2 Maintenance screen approximately 15 minutes.

Once correction is complete, correction date and time will be displayed in the column where previous correction date and time were located.

Note Press the STARTSTOP key during instrument baseline correction to halt correction operation.

If correction operation is halted, the Not corrected will be displayed in the column where previous correction date and time were located.

A problem may occur if measuring is performed with instrument baseline correction in the halted status.

Be sure to rerun instrument baseline correction after resolving problems whenever this operation is halted for whatever reason.

A warning message will be displayed if one hour has not elapsed from when the power was turned ON Checking of Baseline Flatness To implement baseline flatness inspection, the instrument power supply must be turned ON for at least one hour prior to inspection.

A warning message will be displayed if one hour has not elapsed from when the power was turned ON.

Cary 50 Service Manual